出一个自用的rtorrent.rc
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.
# Minumum amount of peers to connect per torrent, if available.
min_peers = 40
# Minumum amount of peers to connect per torrent.
max_peers = 500
# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 20
# Maximum number of simultanious uploads per torrent.
max_uploads = 15
# Global download rate in KiB. "0" for unlimited.
download_rate = 0
# Global upload rate in KiB. "0" for unlimited.
upload_rate = 28
# Default directory to save downloaded files. Note it doesn't support
# space yet.
directory = /mnt/nas/yutech/download/rtorrent/work/
# Watch a directory for new torrents, and stop those that have been deleted.
schedule = watch_directory,5,5,load_start=/mnt/nas/yutech/download/rtorrent/dl/*.torrent
schedule = untied_directory,5,5,stop_untied=
# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M
# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /mnt/nas/yutech/download/rtorrent/session
# The ip address reported to the tracker.
#ip = rakshasa
# The ip address the listening socket and outgoing connections is
# bound to.
#bind = rakshasa
# Port range to use for listening.
port_range = 51777-51780
# Start opening ports at a random position within the port range.
#port_random = no
# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no
# Set whetever the client should try to connect to UDP trackers.
#use_udp_trackers = yes
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa
#
# Do not modify the following parameters unless you know what you're doing.
#
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10
# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100
# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10
# Max number of files to keep open simultaniously.
#max_open_files = 128
# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default>
# Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"
# Remove a scheduled event.
#schedule_remove = "ip_tick1"
# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=100,100M,500"
# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
encryption = allow_incoming,enable_retry,prefer_plaintext
# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
dht = on
# UDP port to use for DHT.
#
dht_port = 6881
# Enable peer exchange (for torrents not marked private)
#
peer_exchange = yes
#
# Do not modify the following parameters unless you know what you're doing.
#
encoding_list = UTF-8
umask = 0000
on_finished = move_complete,"execute=mv,-u,$d.get_base_path=,/mnt/nas/yutech/download/rtorrent/movie/ ;d.set_directory=/mnt/nas/yutech/download/rtorrent/movie/"
scgi_port = 127.0.0.1:5000 |
发表于 2011-8-7 22:06:55
楼主
